Ваша корзина пуста.
15 сентября 2019 г. 12:50:45

Over all Guide - read this FIRST!

one month ago
#3777 Цитировать
Hello,

This entire process is in desperate need of an overhaul!

After spending $55 on firmware for the Mavic 2 Pro, I am no closer to removing the NFZ than I was once I bought my drone.

I have been patient, thoroughly read the instruction manual, yet my drone is stuck at the 15% mark once the "Flashing" has started.

I've let it sit for over 10 minutes, I have disconnected the drone as per the instructions, I have made sure that "Run As Administrator" are selected -- and nothing.

PLEASE, fix this. Please.

Thanks,

James
0
28 days ago
#3799 Цитировать
I got the same situation!

Always stop at 15%,
and it was really desperated for me!



James wrote:
Hello,

This entire process is in desperate need of an overhaul!

After spending $55 on firmware for the Mavic 2 Pro, I am no closer to removing the NFZ than I was once I bought my drone.

I have been patient, thoroughly read the instruction manual, yet my drone is stuck at the 15% mark once the "Flashing" has started.

I've let it sit for over 10 minutes, I have disconnected the drone as per the instructions, I have made sure that "Run As Administrator" are selected -- and nothing.

PLEASE, fix this. Please.

Thanks,

James
0
26 days ago
#3805 Цитировать
Hi,
I want modified software for Mp1 pro bird.  I see there is a problem quite a lot, is it true for Mp1 or justh Mp2?  Thanks for the answers!
Question: am I installing the new software, is mavic connected to the remote control?
0
25 days ago
#3811 Цитировать
good morning,
I bought the package and I connected my M2Z by swapping the instructions. I just forced the FCC and changed the speed to sport and normal mode. how can I tell if the drone is in fcc mode? unfortunately I have Dji Smart Controller .
thank you
0
24 days ago
#3815 Цитировать
Has anyone had success with NLD on a Mavic Air? Thanks in advance for your reply!
0
22 days ago
#3835 Цитировать
If you have upgraded via GO or using DJI Assistant to firmware V01.00.0400, or V01.00.0300 and NOT used NLD to do so on or after 7/19/19 then you have a new "feature" in your firmware called Anti Rollback. You will know this if no matter what you try to do, NLD will not go past 15% when trying to downgrade firmware. NLD does a firmware module check and at 15%, the firmware flash is started. The actual firmware flash is only started after the 15% module check. With the "anti-rollback" firmware from DJI, NLD stops at 15% and will not actually start the firmware flash.

DJI has silently changed their V01.00.0400 and .0300 firmware and introduced a previously unused anti-rollback feature - WITHOUT TELLING ANYONE!!!!

This means that they don't want you using NLD to downgrade your firmware to V01.00.0100, likely as this is a known exploited firmware!

Currently, trying to use NLD in this situation means a downgrade will appear "stuck" at 15%, and never kick off the firmware flash. Until we can "fix" this DJI problem, you will not be able to get to V01.00.0100. Once we have a solution, we will announce it on our NLD homepage.

If you have upgraded via NLD to 01.00.0400, you will be fine and able to continue to use NLD to downgrade your firmware, the version we offer for re-flash is clean and doesn't have this "lock feature" enabled. This is stock DJI firmware, but we downloaded the "clean" version before the silent update.

For future reference. DO NOT USE DJI ASSISTANT!! OR UPGRADE FIRMWARE VIA THE GO APP!! The DJI GO app connects directly to DJI and downloads firmware from DJI.
0
20 days ago
#3845 Цитировать
I have read the entire user guide and when I remove the NFZ it says "firing magic bullet, blah blah blah" reboots and then I walk outside to try it and it doesn't work. I'm reflashing the firmware now, but you can bet if it doesnt work this time I'll be disputing the charges for this software with my bank.
0